Buster & Punch
Caged Wet / Wall / Large
107.900 kr
Buster & Punch
Caged Wet / Wall / Large
107.900 kr
DESIGN: Buster & Punch.
A luminaire made from matt black metal and glass cage, complete with a cast metal back panel. It features a solid metal, cross knurled, lamp holder with B+P signature coin screws. IP44 rated and suitable for interior, exterior and bathroom use. Available in steel, brass and gun metal finishes.
DIMENSIONS.
H: 488 mm. / W: 180 mm. / 100 mm.
E27 / 200-240V / IP44.
Protected against water splashed from all directions, with limited ingress. In some cases, moisture may get into the cage but will evaporate after a short time through drainage holes.
Related products
-
Vaarnii
1001 Hans Pendant
103.900 kr
Visit product page →DESIGN: Hans-Agne Jakobsson
The warm glow of light filtering through pine veneer combined with an unexpectedly graphic and elemental form is the enduring appeal of these iconic designs by Hans-Agne Jakobsson. When Vaarnii began exploring the use of pine wood in lighting design, it quickly became clear that the iconic designs of Hans-Agne Jakobsson from the 1960’s could not be bettered. Pine is used efficiently; it’s tone and grain are employed to maximum effect in designs that project material mass but boast actual lightness. Vaarnii has re-engineered three of Jakobsson’s pendant designs using solid Finnish pine to support circular strips of high-quality pine veneer, reintroducing these classic 20th century designs to the market after decades of absence.
Handcrafted in Finland.
-
Vaarnii
1002 Hans Pendant
133.900 kr
Visit product page →DESIGN: Hans-Agne Jakobsson
The warm glow of light filtering through pine veneer combined with an unexpectedly graphic and elemental form is the enduring appeal of these iconic designs by Hans-Agne Jakobsson. When Vaarnii began exploring the use of pine wood in lighting design, it quickly became clear that the iconic designs of Hans-Agne Jakobsson from the 1960’s could not be bettered. Pine is used efficiently; it’s tone and grain are employed to maximum effect in designs that project material mass but boast actual lightness. Vaarnii has re-engineered three of Jakobsson’s pendant designs using solid Finnish pine to support circular strips of high-quality pine veneer, reintroducing these classic 20th century designs to the market after decades of absence.
Handcrafted in Finland
-
Vaarnii
1002 Hans pendant XL
244.900 kr
Visit product page →DESIGN: Hans-Agne Jakobsson.
Big, brazen, and a whole lot of pine, the Hans Pendant XL delivers a substantial dose of iconic design. After re-engineering Hans-Agne Jakobsson’s characteristic sixties lighting, Vaarnii understood that the designs innovative lightweight construction could be extended even further. The super-sized Hans Pendants uses the same concentric circles of veneer and sophisticated interior structure of solid Finnish pine as their smaller-sized siblings but tests the limits of lighting manufacture with their scale. More softly filtered light, more pine surface, more imposing, the 70 cm 1002 Hans Pendant XL brings maximum impact to interior spaces with its brutal scale and metres of finest pine veneer.
The Hans series of lighting is made in Finland using solid pine for internal structure and the finest pine veneer for exterior surfaces. As every light is handmade using a natural material, each object is subject to subtle variations in symmetry. Every Hans light is therefore unique.
Pine is an especially characterful wood. As a result of naturally occurring oils and resins, pine changes colour as it ages. Vaarnii uses both pine heartwood and pine sapwood. These two different types of wood mature at different speeds, resulting in a beautifully stripped surface. This exciting patterning is a temporary stage and should be enjoyed while it occurs. Your Vaarnii pine product will gradually even out to a rich honey tone over the course of several years.
DIMENSIONS.
H: 45 cm. x W: 70 cm.
-
Vaarnii
1003 Hans Pendant
179.900 kr
Visit product page →DESIGN: Hans-Agne Jakobsson
The warm glow of light filtering through pine veneer combined with an unexpectedly graphic and elemental form is the enduring appeal of these iconic designs by Hans-Agne Jakobsson. When Vaarnii began exploring the use of pine wood in lighting design, it quickly became clear that the iconic designs of Hans-Agne Jakobsson from the 1960’s could not be bettered. Pine is used efficiently; it’s tone and grain are employed to maximum effect in designs that project material mass but boast actual lightness. Vaarnii has re-engineered three of Jakobsson’s pendant designs using solid Finnish pine to support circular strips of high-quality pine veneer, reintroducing these classic 20th century designs to the market after decades of absence.
Handcrafted in Finland.
